Introduction Essay, Research Paper
In this experiment we are trying to find the percentage of water in Barium Chloride
Dihydiate. During the experiment you must pay close attention to everything done. We
are going to try to stay below a 8 percent error. When timing, make sure you only have
the crucible over the bunson burner for 10 minutes, no more, no less. Be aware of how
dangerous this chemical can be, so please be careful.
Located below is a list of all the materials you will need to complete this
experiment. Please make sure you and you lab partner(s) know how to use this
equipment.
Equipment / Materials
Goggles Bunson Burner
Ring Stand Iron Ring
Iron Triangle Iron Square
Computer Computer Program
Scale Chemical (BACL2)
Scoop Crucible/Crucible cover
Crucible Tongs Matches
Safety
You must pay close attention to everything at all times. Ladies with their hair not
tied back should do so do to the fact that their hair could catch fire while using the bunson
burner. Before you start the experiment, take notice to where all the safety equipment
is. You must know where the fire extinguisher is, emergency shower/eye wash, and the
call for help button. Make sure you are wearing your goggles while doing this lab. When
washing out the crucible do not turn the water pressure up all the way because the water
could splash back into your face. If an emergency does occur, please remain clam and
think rationally.
Procedure
This experiment can be very exciting if you know what you are doing. Before I
started the experiment, I set up my lab. I put together my Ring stand and attached the
bunson burner up to the gas valve. Before I light the flame, I asked my partner to turn the
two gas valves on while I light the flame with a match. Now that my flame was light, I
adjusted the air flowing into the flame.
Now I was ready to start with the experiment. When handling the crucible do not
touch it with your hands, only use the crucible tongs. My partner cleared the scale and I
weighed the crucible with its lid, and it came to 17.09. I removed the crucible and added
the BACL2.2H2O. Placed the crucible and lid back on the scale and got the weight of
18.33. Now it was time to place the crucible over the bunson burner. I carefully placed
the lid on the crucible and carry the crucible over to the bunson burner and placed it on the
iron triangle and. And placed the crucible directly over the flame and set a timer to 10
minutes.
While I was waiting for the experiment to finish, my partner decided that she
wanted to start another experiment. So we prepared the scale and crucible and
re-weighed everything. By the time we had finished, the alarm sounded and we quickly
took the crucible off the flame. We left the crucible cool for another 10 minutes and then
re-weight it and it came to 18.15.
Christy started to put all the weights in the computer and to our big surprise we
got a 0.23 experimental error and a 1.59 percent error. We were so glad that the
experiment went to well that we let it get to our head. We thought we would do even
better on our next experiments, but we were wrong. Our percentages started to raise and
we realized that we were not doing something right. We noticed that we were not
watching the clock and completely messed up the experiment.
Percent of water in Barium Chloride Dihydrate Experiment
Mass of Crucible and Cover———————————————————-17.09
Mass of Crucible, Cover and BACL2.2H2O————————————– 18.33
Mass of Crystallized BACL2.2H2O———————————————— 1.24
Mass of Crucible and Cover———————————————————- 17.09
Mass of Crucible, Cover and Anhydrous BACL2 —————————— –18.15
Mass of Anhydrous BACL2——————————————————— 1.06
Mass of Crucible, Cover and BACL2.2H2O————————————— 18.33
Mass of Crucible, cover and Anhydrous BACL2——————————— 18.15
Mass of water lost by heating———————————————————–.18
Percent water in Crystallized BACL2.2H2O—————————————14.52
Theoretical Percent of H2O in BACL2.2H2O————————————14.75
Mass of Crystallized BACL2.2H2O————————————————-1.24
Mass of Anhydrous BACL2 ——————————————————–1.06
Mass of water lost by heating———————————————————-.18
Experimental Error———————————————————————–.23
Percent Error—————————————————————————-1.59
Error
Most of my error was caused by the fact of the flame not staying still in one spot.
The ventilator on the ceiling was blowing air down onto the flame and caused the flame to
flicker.
Conclusion
This experiment was very interesting and informative. We learned the value of
paying attention to what we are doing and to not let our mines wonder.