Microprocessors Essay Research Paper Microprocessors

Microprocessors Essay, Research Paper

Microprocessors

Inside of the mysterious box that perches ominously on your desk is one of

the marvels of the modern world. This marvel is also a total enigma to most of

the population. This enigma is, of course, the microprocessor. To an average

observer a microprocessor is simply a small piece of black plastic that is found

inside of almost everything.

In How Microprocessors Work they are defined as a computer’s central

processing unit, usually contained on a single integrated circuit (Wyant and

Hammerstrom, 193). In plain English this simply means that a microprocessor is

the brain of a computer and it is only on one chip. Winn L. Rosch compares them

to being an electronic equivalent of a knee-joint that when struck with the

proper digital stimulus will react in the exact same way each time (Rosch,37).

More practically a microprocessor is multitudinous transistors squeezed onto as

small a piece of silicon as possible to do math problems as fast as possible.

Microprocessors are made of many smaller components which all work

together to make the chip work. A really good analogy for the way the inner

workings of a chip operate can be found in How Microprocessors Work. In their

book, Wyant and Hammerstrom describe a microprocessor as a factory and all of

the inner workings of the chip as the various parts of a factory (Wyant and

Hammerstrom, 71-103). Basically a microprocessor can be seen as a factory

because like a factory it is sent something and is told what to do with it. The

microprocessor factory processes information. This most basic unit of this

information is the bit. A bit is simply on or off. It is either a one or a zero.

Bits are put into 8 bit groups called bytes. The number 8 is used because it is

offers enough combinations to encode our entire language (2^8=256). If only 4

bits are used only (2^4=16) combinations would be possible. This is enough to

encode 9 digits and some operations. (The first microprocessors powered

calculators) A half byte is called a nibble and consists of 4 bits. In the world

of computer graphics the combination of bits is easier seen. In computer

graphics bits are used to make color combinations, thus with more bits more

colors are possible. Eight bit graphics will display 256 colors, 16 bit will

display 65,536, and 24 bit graphics will display 16.7 million colors. The bus

unit is described as the shipping dock because it controls data transfers, and

functions between the individual pieces of the chip. The part of the chip that

performs the role of a purchasing department is called the prefetch unit. It’s

job is to make certain that enough data is on hand to keep the chip busy. The

decode unit performs the role of a receiving department. It breaks done

complicated instructions from the rest of the computer into smaller pieces that

the chip can manipulate more readily. The control unit is compared to the

person who oversees the workings of the entire factory. It is the part of the

chip that keeps all the other parts working together and coordinates their

actions. The arithmetic logic unit is compared to the assembly line of the

factory. It is the part of the microprocessor that performs the math operations.

It consists of circuitry that performs the math and the registers which hold the

necessary information. The memory management unit is likened to the shipping

department of this digital factory. It is responsible for sending data to the

bus unit. Together all of the individual pieces support each other to make this

digital symbiosis work as fast as possible.

To an outsider, computer nerd vernacular and all other forms of computer

people esoteric may or may not be considered frightening. Probably the most

confused term in microprocessor performance is Megahertz (MHz). Basically these

are millions of cycles per second. This is a measurement of chip speed but is

better considered the RPM of the chip (Knorr, 135). For example a 486 100 MHz

processor cannot touch the speed of a Pentium running at only 60 MHz. This is

because the Pentium packs more power and can do more per clock cycle. The

computer bus is the data line that connects the microprocessor the rest of the

computer. The width of the bus (how many bits it consists of) controls how much

data can be sent to the chip per clock cycle. MIPS or millions of instructions

per second is simply how many instructions the chip can perform in one second

divided by 1,000,000. RISC is a commonly used term in the computing world also.

It is an acronym for Reduced Instruction Set Computer. Chips that incorporate

RISC technology basically rely on simplicity to enhance performance. Motorola

chips use this technology. The opposite of RISC is CISC which stands for Complex

Instruction Set Computer. These chips use more hardwired instructions to speed

up the processing process. All Intel PC products fall into this category.

Pipelining, superscalar architecture, and branch prediction logic are currently

technological buzzwords in the computer community presently. These technologies

can be found in newer chips. Pipelining allows the chip to seek out new data

while the old data is still being worked on (Wyant and Hammerstrom, 161).

Superscalar architecture allows complex instructions to be broken down into

smaller ones and then processed simultaneously through separate pipelines (Wyant

and Hammerstrom, 161-163). Branch prediction logic uses information about the

way a program has behaved in the past to try to predict what the program will

do next (Wyant and Hammerstrom, 165). Bus speed is simply the speed in MHz at

which the data bus travels. This is relative to how fast the microprocessor can

communicate with the rest of the computer. A register is the part of the chip

that hold the information that the chip is currently manipulating. The width of

the register in bits is relative to how much data the chip can process

simultaneously. Using very long instruction words is simply using instructions

larger than 16 bits to increase the amount of data the chip can be sent at once.

A new tool being used in making chips run faster is to place a cache on the chip.

This cache is for holding data that the chip is most likely to need first. Since

the data is stored inside the chip the access time is lowered dramatically. In

the future more and more of the computer will be integrated on the main

processing unit. Line width is also a sign of the technological times. It is

simply how small the smallest feature is on a chip. Basically the smaller the

lines the more transistors can be squeezed onto the wafer and thus increase

performance while cutting manufacturing costs.

Non-technological issues also have a major effect on the microprocessing

world. One such issue is heat. This may sound trivial but a Pentium chip can and

will burn the skin of a person who touches one that has been running for longer

than a few minutes. Without a fan most modern chips will melt and or destroy

themselves. To combat this, large aluminum heat sinks are attached to the chips

and a large fan is placed in the case. Some users prefer to use a separate fan

above the heat sink for added insurance. Operating voltages can also add to the

heat problem. Chips run from either 3.3 or 5 volts. Three and three tenths volts

is preferred now because with less power less heat is generated and in the case

of laptops battery life is extended.

Credit for the invention of the microprocessor is given to Intel. This

first microprocessor was the 4004 and was released in 1971. This single chip

matched the performance of the room size computer ENIAC from the fifties (Wyant

and Hammerstrom, 19). This chip could only support a four bit bus. These four

bits only offered the possibility of coding 16 symbols (2^4=16). Sixteen symbols

was enough for digits 1-9 and then some operators. This limited the 4004 to

calculator usage. The 4004 ran at 108 kHz which is 1/10 of 1 MHz (Rosch, 66).

The smallest feature on the chip measured 10 microns and contained 2300

transistors. The next generation of Intel chips used a 8 bit data bus. The

first member of this generation was released in 1972 and was called the 8008.

This chip was the same as the 4004, but it had 4 more bits on each register.

This chip had enough bits to code 256 symbols (2^8=256). This number is easily

enough to encode our alphabet, numerals, punctuation marks, etc. The 8008 also

ran a little faster than the 4004 with its speedy clock of 200 kHz. The 8008

contained 3500 transistors and had line widths 10 microns. Both chips had a MIPS

of 0.06 (Rosch, 66). The next member of the Intel family was born in 1974 and

was called the 8080. This chipped was intended to handle byte sized data (8 bit).

The 8080 contained 6000 transistors and had 6 micron technology. This chip

performed at 0.65 MIPS and had an internal clock speed of 2 MHz. This was one of

the first chips to have the capabilities of running a small computer (Rosch,

66). In June of 1978 the 8086 family was released by Intel. These chips used 16

bit registers. The fastest chip in this series ran at 10 MHz and could

execute.75 MIPS. This chip forced engineers of the time to begin developing

fully 16 bit devices, which were more expensive than their 8-bit brethren.

Because of this, the 8086 family was considered ahead of it’s time (Rosch, 67-

68). A year later Intel introduced the 8080. This chip was a step backwards in

chip evolution with it’s 8 bit data bus. The 8080 could process.64 MIPS with

it’s 6000 transistors. The 8080 used 6 micron technology. This chip is worth

mentioning primarily because IBM chose to use it in it’s first personal computer.

IBM was able to use the 8088 with existing 8 bit hardware, which was more cost

effective. Later IBM began using the 8086 in it’s newer systems (Rosch, 68). In

1982 Intel released the 80286. The 286 family was available in clock speeds of 8,

10, and 12 MHz that could execute 1.2, 1.5, and 1.66 MIPS respectively. The

80286 contained 134,000 transistors with 1.5 micron technology. These chips all

used a 16 bit data bus and were used by IBM in it’s AT models. This was also the

first chip to use virtual memory, or using disk space as RAM (Random Access

Memory). To allow full downward compatibility the 286 was designed to have two

operating modes. These modes are real and protected mode. Real mode mimics the

operation of an 8086. Protected mode allows multiple applications to be run

simultaneously and not interfere with each other (Rosch, 70-71). The next member

to the Intel family was added in November 1985 and was the 80386. These chips

are offered in speeds of 16, 20, 25, 33 MHz and can process 5.5, 6.5, 8.5, and

11.4 MIPS respectively. The number of transistors in the 80386 is 275,000 with

1.5 micron technology. The 386 family doubled the register size to 32 bits. Also

the 386 uses 16 bytes of prefetch cache that the chip uses to store the next few

instructions. The 386 has three models which are called the 386DX, 386SX, and

the 386SL. The 386DX was the original and most powerful. The 386SX is a more

economical sibling to the DX. It is basically scaled down, less powerful DX.

Also the SX uses a 16 bit data bus. The SL also uses 16 bit buses but it

includes power saving features targeted at notebook usage. The SL uses 1.0

micron technology and contains 855,000 transistors (Rosch, 72-78).

The 80486 family was introduced in April 1989 and became a “better 386″

(Rosch, 78). The 486 was originally released in a DX model with speeds of 25, 33,

and 50 MHz that processed 20, 27, and 41 MIPS respectively. The DX also contains

a math coprocessor or floating point unit that helps speed up math operations.

The 486DX uses a 32 bit bus and contains 1,200,000 transistors. It uses 1.0

micron technology in the 25 and 33 MHz models, but in the 50 MHz model uses 0.8.

The next to be released was the 486SX. The SX was designed to cut cost at the

price of not having a math coprocessor. As a result the SX will not perform as

well as the DX in math intensive operations. The SX contains 1,185,000

transistors and uses the same technology as the DX. The SX is available in 16,

20, 25, and 33 MHz models that process 13, 16.5, 20, and 27 MIPS respectively.

To add the power of a FPU (Floating Point Unit) to the SX Intel released the

OverDrive upgrade processors in March 1992. The first, the 486DX2, incorporated

clock doubling technology. These chips operate at double the bus speed. These

chips are available in 50 and 66 MHz models that can process 41 and 54 MIPS

respectively. The 50 MHz model was designed to replace the 25 MHz 486SX and the

66 MHz model was for the 33 MHz 486SX. The OverDrive chips contain 1.2 million

transistors. The next to be released was the SL model which was, like the 386SL,

targeted at laptop usage. The SL contains 1.4 million transistors and can

process 15.4, 19, and 25 MIPS while running at 20, 25, and 33 MHz respectively.

The 486DX4 was the next OverDrive chip to be released. It contains clock

tripling technology. The DX4 can turn a 33 and 25 MHz 486’s into DX4-100 and

DX4-75 respectively. These chips can process 60 and 81 MIPS running at 75 and

100 MHz respectively. The DX4 uses 0.6 micron technology (Rosch 84-85).

The next addition to the Intel family was the Pentium. The Pentium was

originally released in a 60 MHz model that operated at 5 volts. This chip

contains 3,100,000 transistors and can process 100 MIPS. The next to be released

was the 66 MHz model. It uses the same technology but is a 3.3 volt chip and can

process 112 MIPS. Currently the Pentium is available in 66, 75, 90, 100, 120,

133, 150, and 166 MHz models. Beyond the 75 all Pentiums use 0.6 micron

technology. A 180 MHz is slated for future release. The Pentium family is, like

all of Intel’s chips, uses CISC technology. Also they use pipelining,

superscalar architecture, and branch prediction logic. A Pentium OverDrive is

also available for upgrading 486 systems to Pentium technology. The Pentium

OverDrive is available in a 63 and 83 MHz version (Rosch, 85-87).

After the Pentium, the only more advanced chip Intel has for personal

use is the Pentium Pro. This chip has only been available for a short time and

is targeted at workstation and server usage. It will only run Windows NT and

native 32 bit software at an increased speed. When using 16 bit software, the

less powerful Pentium will outperform its larger sibling. The Pentium Pro also

contains 256K (256,000 bytes) of on chip cache memory.

The only certainty in the future of microprocessors is constant

improvement. One prediction for the future is called Moore’s Law. This

prediction is named after Intel cofounder Gordon Moore who presented it in 1965.

The law states the transistor densities will double every two years. Line width

is also continuing to shrink and is estimated to be at 0.2 microns by the turn

of the century. When all is considered the future of computers is very exciting

(Wyant and Hammerstrom, 184-185).

Bibliography

Knorr, Eric. “From 586 to Pentium Pro: Choosing Your Dream PC.” PC World

February 1996: 133-142.

Rosch, Winn L. The Hardware Bible. Indianapolis: SAMS, 1994.

Wyant, Gregg, Hammerstrom, Tucker. Intel, How Microprocessors Work.

Emeryville: Ziff-Davis, 1994.